Importing Sound Fonts - Neo CFX Saber

Step 1

Remove the microSD card from your saber and connect it to a computer.

In the root directory, create a new folder in the following format:

[Number]-[Sound_Font_Name_Without_Spaces]

So if you downloaded KSith's "The Light" and are installing it as your 17th font, the folder should be named:

17-THE_LIGHT

Place all of the files from the sound font you downloaded into the new folder.

Step 2

Check that the 'font_config.txt' file is present in the new folder.

If it is missing, copy it over from another sound font folder into the new folder.

Each 'font_config.txt' file contains parameters that define that sound font's behavior when it is active.

View the pages linked below to learn more about these parameters.

View 'Advanced Color Customization' to learn more

View 'Advanced Blade Animations' to learn more

Importing Sound Fonts - Neo Proffie Saber

Step 1

Remove the microSD card from your saber and connect it to a computer.

In the root directory, delete both 'presets.ini' and 'presets.tmp' if they are present.

Step 2

Copy the entire contents of your Neo Proffie Saber's microSD card and save it locally to your computer.

Safely eject the microSD card from your computer, insert it back into the Neo Proffie Saber's soundboard, and set it aside.

For the next few steps we will be working exclusively with the contents you just saved locally to your computer.

Create a new folder inside the root directory and name it in following format:

[number]-[sound_font_name_without_spaces]

For this guide, we will be naming the example sound font:

19-EX_SOUNDFONT

Step 3

Navigate to 'extra > ProffieOS > config'.

Refer to the list below to find and open the 's3config' file that matches your hilt/chassis configuration with a code editor like Notepad++.

Step 4 - Blade Style

All of a Neo Proffie Saber's behaviors are hard-coded into each individual sound font, so the easiest way to add a sound font is to copy-and-paste the code from a pre-existing one. In the guide below, we transplant a blade style from '1-SABERTRIO' to '18-TYTHONIAN_CRYSTAL'.

Find the code for the sound font with the blade style you would like to copy.

Select and copy all lines of code from “#-SOUNDFONT_NAME;common” to "StylePtr(), “Soundfont Name”},” as shown in the example below.

If your saber is a Krosgaard, there is an additional segment of code for the quillon blades that you will need to copy.

Find the code for the sound font you would like to edit and replace its style code with the one you copied.

Ensure that the name of the sound font you are editing (shown below in Red) matches the name of the sound font’s folder exactly.

If you want to use other blade styles not natively found on your Neo Proffie Saber, you can find a massive range of blade styles in Fett263's Style Library.

Fett263 - ProffieOS7 Style Library

Take the “1-SABERTRIO;common” (or whichever blade profile you chose) code you copied and paste it below the code of your new sound font.

Ensure that the new blade profile is properly renamed to exactly match (case-sensitive) the name of the new sound font's folder, otherwise your ProffieBoard will not recognize it.

Step 5 - Blade Color

The blade color is defined in the segment of code you copied in the previous step, near the start of 'StylePtr'. If you want to change it, you can either use the predefined color names or an RGB value.

If your saber is a Krosgaard, there is an additional segment of code for the quillon blades that you will need to edit.

Go to the Blade Color page to find all of the predefined color names in the Neo Proffie Saber section, and a list of RGB color values in the Neo CFX Saber section.

View 'Blade Color' to learn more

To change a sound font's blade color using RGB values, you will need to write it as Rgb<0,0,0> as shown below.

And if your saber is a Krosgaard, there are additional code segments for the quillon blades that need to be modified as well.

Step 6 - Preparing to Reflash

You will now need to reflash your ProffieBoard. This means that you will be replacing the contents of your Neo Proffie Saber's microSD card with the content you saved/edited locally on your computer.

Toggle the killswitch to OFF.

Using the provided data cable, connect one end to your saber’s USB-C port or Micro-USB port (for Legacy Chassis System) and the other to a USB port on your computer.

Your computer should now detect your Neo Proffie Saber. On your computer, navigate to the 'extra > ProffieOS' folder and open the 'ProffieOS.ino' file. Arduino IDE should automatically launch with the file loaded.

In Arduino, ensure “Serial + Mass Storage” is selected for USB Type option in the Tools drop down menu as shown below:

For the ProffieBoard V3.9, make sure to select "SDCARD (SDIO High Speed)" from the DOSFS option in the Tools drop down menu as shown below:

Similarly, ensure Port is selected to “COM4 (Proffieboard)” as shown below:

You will need to select the appropriate config file that matches your saber hilt. To do that, delete the "//" before the correct config file name:

[OPTIONAL] Reverting to Fett263's Original Button (prop) File

Step 7 - Reflashing

You are now ready to reflash your Neo Proffie Saber’s firmware. Click the upload button shown below to begin the flashing process.

Red texts should begin showing in the lower terminal screen and eventually a progress bar should be displayed. If the progress bar does not show, click the upload button again.

Once the reflashing process is completed, your Neo Proffie Saber will emit a distorted sound. This is normal and your saber now has the latest Sabertrio Proffie Preconfiguration. Unplug the cable and toggle the killswitch to power the saber to ON.

Enjoy your updated Neo Proffie Saber! Remember to adjust the blade length parameter on your saber if your Neo Blade is shorter than 36".

If you want to dive deeper, you can find out more through the links below.

ProffieOS Documentation - ProffieBoard Setup

The Crucible - ProffieOS - Help/Discussion Forum

Fett263 - ProffieOS7 Style Library